Annexes¶
Annex 1: commands for ground SDL04¶
AT&F6 (Factory defaults for a PP master)
ATS128=2 (400 MHz Frequency Hopping)
ATS108=30 (1 W to transmit power)
ATS104=1893 (Network Address. All radios in a given network must have the same Network Address, but different networks must have different address)
ATS105=1 (Unit address, masters must have 1)
ATS102=1 (Serial baud rate for serial port. It must be the same for the connected device: 115200 bps for this case)
ATS113=2 (Maximum number of times that a packet will be retransmitted)
ATP0= (Set available primary frequencies for the radio)
411.000000
472.000000
443.000000
464.000000
415.000000
436.000000
467.000000
478.000000
419.000000
460.000000
421.000000
472.000000
443.000000
464.000000
445.000000
426.000000
427.000000
468.000000
429.000000
440.000000
431.000000
412.000000
433.000000
464.000000
445.000000
436.000000
437.000000
478.000000
429.000000
410.000000
461.000000
452.000000
443.000000
454.000000
465.000000
416.000000
427.000000
418.000000
449.000000
470.000000
431.000000
452.000000
433.000000
414.000000
465.000000
476.000000
437.000000
428.000000
419.000000
480.000000
ATP1= (Set available secondary frequencies for the radio)
411.000000
472.000000
443.000000
464.000000
415.000000
436.000000
467.000000
478.000000
419.000000
460.000000
421.000000
472.000000
443.000000
464.000000
445.000000
426.000000
427.000000
468.000000
429.000000
440.000000
431.000000
412.000000
433.000000
464.000000
445.000000
436.000000
437.000000
478.000000
429.000000
410.000000
461.000000
452.000000
443.000000
454.000000
465.000000
416.000000
427.000000
418.000000
449.000000
470.000000
431.000000
452.000000
433.000000
414.000000
465.000000
476.000000
437.000000
428.000000
419.000000
480.000000
AT&W (Store active configuration into the non-volatile memory)
ATA (Set the device to online mode)
Annex 2: commands for air SDL04¶
AT&F7 (Factory defaults for a Point to Point slave)
ATS128=2 (400 MHz Frequency Hopping)
ATS108=30 (1 W to transmit power)
ATS104=1893 (Network Address. All radios in a given network must have the same Network Address, but different networks must have different address)
ATS105=2 (Unit address, each unit must have a unique identifier in a network).
ATS102=1 (Serial baud rate for serial port. It must be the same for the connected device: 115200 bps for this case)
ATS113=2 (Maximum number of times that a packet will be retransmitted)
ATP0= (Set available primary frequencies for the radio)
411.000000
472.000000
443.000000
464.000000
415.000000
436.000000
467.000000
478.000000
419.000000
460.000000
421.000000
472.000000
443.000000
464.000000
445.000000
426.000000
427.000000
468.000000
429.000000
440.000000
431.000000
412.000000
433.000000
464.000000
445.000000
436.000000
437.000000
478.000000
429.000000
410.000000
461.000000
452.000000
443.000000
454.000000
465.000000
416.000000
427.000000
418.000000
449.000000
470.000000
431.000000
452.000000
433.000000
414.000000
465.000000
476.000000
437.000000
428.000000
419.000000
480.000000
ATP1= (Set available secondary frequencies for the radio)
411.000000
472.000000
443.000000
464.000000
415.000000
436.000000
467.000000
478.000000
419.000000
460.000000
421.000000
472.000000
443.000000
464.000000
445.000000
426.000000
427.000000
468.000000
429.000000
440.000000
431.000000
412.000000
433.000000
464.000000
445.000000
436.000000
437.000000
478.000000
429.000000
410.000000
461.000000
452.000000
443.000000
454.000000
465.000000
416.000000
427.000000
418.000000
449.000000
470.000000
431.000000
452.000000
433.000000
414.000000
465.000000
476.000000
437.000000
428.000000
419.000000
480.000000
AT&W (Store active configuration into the non-volatile memory)
ATA (Set the device to online mode)
Annex 3: commands for ground SDL09¶
AT&F10 (Factory defaults for a PP master)
ATS108=30 (1 W to transmit power)
ATS104=1000 (Network Address. All radios in a given network must have the same Network Address, but different networks must have different address)
ATS105=1 (Unit address. Every unit in a PP Network must have a unique unit address. Masters must have 1 as address)
ATS102=1 (Serial baud rate for serial port. It must be the same for the connected device: 115200 bps for this case)
ATS113=2 (Maximum number of times that a packet will be retransmitted)
ATS103=2 (RF link rate. All radio within a particular network must be configured with the same one, 276480 bps for this case)
AT&W (Store active configuration into the non-volatile memory)
ATA (Set the device to online mode)
Annex 4: commands for air SDL09¶
AT&F11 (Factory defaults for a PP slave)
ATS108=30 (1 W to transmit power)
ATS104=1000 (Network Address. All radios in a given network must have the same Network Address, but different networks must have different address)
ATS105=2 (Unit address. Every unit in a PP Network must have a unique unit address)
ATS102=1 (Serial baud rate for serial port. It must be the same for the connected device: 115200 bps for this case)
ATS113=2 (Maximum number of times that a packet will be retransmitted)
ATS103=2 (RF link rate. All radio within a particular network must be configured with the same one, 276480 bps for this case)
AT&W (Store active configuration into the non-volatile memory)
ATA (Set the device to online mode)
Annex 5: commands for ground SDL24¶
AT&F6 (Sets the factory defaults for a PP master)
ATS108=30 (1 W to transmit power)
ATS104=2397 (Network Address. All radios in a given network must have the same Network Address, but different networks must have different address)
ATS105=1 (Unit address, masters must have 1)
ATS102=1 (Serial baud rate for serial port. It must be the same for the connected device: 115200 bps for this case)
ATS113=2 (Maximum number of times that a packet will be retransmitted)
ATS103=2 (RF link rate. All radio within a particular network must be configured with the same one, 276480 bps for this case)
AT&W (Store active configuration into the non-volatile memory)
ATA (Set the device to online mode)
Annex 6: commands for air SDL24¶
AT&F7 (Sets the factory defaults for a PP slave)
ATS108=30 (1 W to transmit power)
ATS104=2397 (Network Address. All radios in a given network must have the same Network Address, but different networks must have different address)
ATS105=2 (Unit address. Every unit in a PP Network must have a unique unit address)
ATS102=1 (Serial baud rate for serial port. It must be the same for the connected device: 115200 bps for this case)
ATS113=2 (Maximum number of times that a packet will be retransmitted)
ATS103=2 (RF link rate. All radio within a particular network must be configured with the same one, 276480 bps for this case)
AT&W (Store active configuration into the non-volatile memory)
ATA (Set the device to online mode)