Silvus radio (StreamCaster 4200E model)

System Layout

The following image shows the standard connection between Silvus radios and 1xVeronte for operation:

../../_images/silvus_veronte.png

Silvus and Veronte connection

Hardware Installation

A wiring configuration of the PRI cable connected to the PRI port of the radio is required in order to connect to the power supply, ethernet and RS-232.

../../_images/pri_port.png

PRI port connector (mounted in radio)

  • Power supply

../../_images/power_connector.jpg

Female DC Power Jack connector

PRI port connector - Silvus radio

Power connector

PIN Nº

Signal

Signal

2

GND IN

Power -

3

VCC IN

Power +

  • Ethernet

../../_images/rj45_connector.jfif

RJ45 pinout T-568B

PRI port connector - Silvus radio

RJ45 Connector (T-568B)

PIN Nº

Signal

PIN Nº

Signal

Color

4

ETH0_MX2N (RX-)

6

RX-

Green

5

ETH0_MX2P (RX+)

3

RX+

Green-White

6

ETH0_MX1P (TX+)

1

TX+

Orange-White

10

ETH0_MX1N (TX-)

2

TX-

Orange

  • RS-232

The RS-232 from the PRI cable should be connected to the RS-232 of Veronte harness.

../../_images/CS_harness-male_plug_v2.png

CS harness plug

PRI port connector - Silvus radio

CS harness - Veronte

PIN Nº

Signal

PIN Nº

Signal

Color

7

RS232_RXD

19

RS 232 TX

White-Pink

8

RS232_TXD

20

RS 232 RX

Pink-Brown

9

GND

21

GND

White-Blue

Silvus radio configuration

This section shows a basic configuration of the Silvus radio.

First Steps

Follow the steps below to set up the radio

  1. Connect antennas (or attenuators) with male TNC ends to 2 RF ports.

  2. Connect power supply to power port on PRI cable.

  3. Connect non-forked female side of PRI cable to radio’s PRI port.

../../_images/connectors_silvus.png

Silvus connectors

  1. When looking at the rotary multi position switch from the top, pull the knob towards you while rotating the knob towards the 1 position. This turns radio on. LED indicator will turn to fix red.

  2. In order to access the StreamScape graphical user interface (GUI), connect Ethernet (RJ45) connector of PRI cable to Ethernet port of laptop/computer.

  3. Make sure computer is set to static IP address on same subnet as radio.

  1. Open network and sharing menu and click change adapter settings.

../../_images/ethernet1.png

Ethernet connection 1

  1. Select Local Area Connection, right click, and select properties.

../../_images/ethernet2.png

Ethernet connection 2

  1. Select IPv4 and click properties.

../../_images/ethernet3.png

Ethernet connection 3

  1. Set IP address to 172.20.XX.YY (e.g. if the IP of the radio is 172.20.178.203, set the IP 172.20.178.200) and subnet mask to 255.255.0.0. Click OK.

../../_images/ethernet4.png

Ethernet connection 4

  1. Wait for LED indicator to turn to blinking green.

  2. Access StreamScape GUI in web browser. To access, enter IP address of radio into web browser and press enter.

Note

Latest version of Firefox or Google Chrome preferred. IE or others not recommended.

../../_images/initial_menu_silvus.png

Silvus initial menu

  1. User maual can be accessed by clicking the book icon in the GUI (Next to “Basic Configuration” in above screenshot.)

Basic radio configuration

Once the website has been accessed, follow the steps below which show the parameters that need to be modified for correct operation and pairing of the radios.

Note

This is an example of the radio configuration linked to a Veronte air unit.

Note

After making changes to each window, it is important to click on “Save and apply”.

  1. Basic Configuration

../../_images/basic_config_air.png

Basic configuration panel

  • Frequency (MHZ): This defines the frequency of the signal. There is a drop-down menu for frequency selection. We recommend 2220 MHz.

Warning

Be careful when choosing the frequency. The user may see interference with the Wifi frequency band, consult the radio spectrum.

  • Bandwith: This defines the RF bandwidth of the signal. Default value.

  • Network ID: Network ID allows for clusters of radios to operate in the same channel, but remain independent. A radio with a given Network ID will only communicate with other radios with the same Network ID.

  • Link Distance (meters): Set to an approximate maximum distance between any two nodes in meters. It is important to set the link distance to allow enough time for packets to propagate over the air. It is recommended to set the link distance 10-15% greater than the actual maximum distance.

  • Total Transmit Power (requested): This defines the total power of the signal (power is divided equally between the radio antenna ports). Set the appropriate power for each application. The power that has been set is small, as it is sufficient for our tests.

  • Routing Mode: As Large Network mode requires a license and is not available outside USA, we set Legacy mode.

  1. Advanced configuration

../../_images/advanced_config_air.png

Advanced configuration panel

  • Transmit/Receive Channels: Allows user to Enable or Disable each channel on the radio for TX/RX (each RF port is a channel). We have enabled both channels.

  1. Networking. Multicast

../../_images/multicast_air.png

Multicast panel

  • Default Multicast Algorithm: Broadcast.

  • Custom Pruning/Augmenting: Disable.

  1. Serial/USB Setup

../../_images/serial_air.png

RS-232 settings

  • Serial Port Setup: RS-232.

  • RS-232 Serial Port Settings

    • The value of the Baudrate, Data Bits, Parity and Stop Bits parameters must be the same as those configured in Veronte Pipe.

    • Software Flow Control: Disable.

    • Transport Protocol: We recommend UDP. If no data loss can be tolerated, change this setting to TCP on the radio corresponding to the Veronte air unit.

    • Peer IP: This should be the IP address of the radio on the other end of the RS-232. In this example, we must set the IP address of the radio linked to the GND unit.

Note

Both radios (the one connected to the GND unit and the one connected to the AIR unit) have the same configuration except for the Peer IP.

../../_images/serial_gnd.png

Peer IP in radio linked to the GND unit

In addition to these settings, different configurations can be stored in the same radio, on the Multi-Position Switch panel. The user can select the one that will work, with the radio’s switch position.

../../_images/multiposition_switch_air.png

Multi-Position Switch panel

In this example only one configuration has been created.

With the above settings the configuration is finished. Furthermore, this configuration can be saved and downloaded in the Settings Profile window of the Configuration Profiles section.

../../_images/settings_air.png

Settings Profile panel

Before downloading the configuration it is necessary to save it.

../../_images/save_settings_air.png

Save settings

../../_images/download_settings_air.png

Download settings

After configuring both radios with these settings they should be paired. Therefore, if we connect them to the power supply, when we switch them on, the LED will turn from fix red to fix green, this indicates that it is connected to at least one radio. Also, if we connect only one of them to the computer, we can access the StreamScape GUI of both of them.

And, in the Network Topology window of the Network Management section, we can see the link between them.

../../_images/connection_air_gnd.png

Connection between radios

Silvus radio configuration in Veronte Pipe

The only configurations to be made in Veronte Pipe are the following:

  1. Go to Connections -> Serial -> 232

Check that they are the same as the parameter values previously set in the Silvus radio.

../../_images/connection_232.png

RS-232 connection configuration

  1. Go to Devices -> Others -> I/O Manager

RS-232 has to be configured as a bidirectional commgr port.

../../_images/ports_232.png

RS-232 connection configuration

Note

These settings have to be made in both Veronte units (GND and AIR).